YAMAHA 2 STROKE POWERHEAD KITS

PARTS PACKAGE KITS FOR REBUILDING POWERHEADS

Look Here For POWERHEAD KITS FOR U.S. BRAND MARINER OUTBOARDS

These kits contain most all the parts you will commonly need to complete the overhaul of your outboard's powerhead. If the determination has been made that you need to rebuild, we have the necessary items! And the nice part is, you will pay less for the kit than you would for the individual parts, as you save us time in ordering. So you will have all the goodies you need to do the job right.

For motors not listed contact us directly for the specific application. It is likely we can provide the components you need.

UNLIKE MANY OF OUR COMPETITORS, OUR rebuild kits include all of the following items, as required, EXCEPT, as noted:
Smaller YAMAHA outboards are built with pressed together crankshafts, thus the rod and centermain bearings are NOT included with these kits.

HOW TO ORDER

Look for the basic manufacturer and horsepower on the table below, click the appropriate box to go to that area.
Then, just add the kit you need to the shopping cart.

BE SURE to fill out the little separate boxes just below and submit first with MODEL and SERIAL # and the OVERSIZE for the pistons!
OR, you may add this info in the special instructions area of the order form.

  NOTE!! I reiterate, you MUST PROVIDE THE MOTOR MODEL NUMBER as well as the
PISTON OVERSIZE if any (or mention standard otherwise) when ordering. We cannot send you the correct parts otherwise!

  THE FOLLOWING KITS ARE REPRESENTATIVE PRICING ONLY, DUE TO SOME VARIATIONS BETWEEN MODELS / YEARS.
THE MODEL NUMBER IS ESSENTIAL IN BUILDING THE CORRECT KIT FOR YOUR MOTOR.

PLEASE Contact Us FOR SPECIFIC QUOTE IF UNCERTAIN.

YAMAHA 25, 30 KITS
THESE HAVE NO AVAILABLE KITS. We can get pistons for a few but most other components are dealer-only.
YAMAHA 3 CYLINDER KITS INCLUDED BEARINGS VARY; SOME HAVE NON-REPLACEABLE CENTER MAIN AND ROD BEARINGS (PRESSED-TOGETHER CRANKS)
CONTACT US FOR QUOTE DUE TO THE MANY DIFFERENT MODELS MADE. PLEASE HAVE THE MODEL NUMBER OF THE MOTOR READY. MANY OF THESE HAVE NO AVAILABLE KITS
40 & 50 HP 3-CYL 1984-94	Click Image For Larger	STD, +.010, .020, 0.30, .040 No Center or Rod Bearings Available, 1-Piece Pressed Crank	100-252-1x $316.00
40 & 50 HP 3-CYL 1995-UP	Click Image For Larger	STD, +.010, .020, 0.30, .040 No Center or Rod Bearings Available, 1-Piece Pressed Crank	100-252-2x $309.00
60 & 70 HP 3-CYL 1984-UP	Click Image For Larger	STD, +.010, .020, 0.30, .040	100-255-1x $414.00
75, 85, 90 HP 3-CYL	Click Image For Larger	STD, +.010, .020, .030, .040	100-265-1x $760.00
YAMAHA V4, V6 KITS
115, 130 HP V4 1984-92 21.5mm WRIST PIN HOLE Rod Stamped 6E5	Click Image For Larger	STD, +.010, .020, .030, .040	100-270-1x $910.00
115, 130 HP V4 1993-03 23mm WRIST PIN HOLE Rod Stamped 6R5	Click Image For Larger	STD.,+.010, .020, .030, .040	100-275-1x $978.00
V6 90° Carbureted	Click Image For Larger	21.5mm WRIST PIN HOLE 6E5 Rod, VERTICAL Reeds STD.,+010. .020, .030, .040	100-270-2xP $1,350.00
V6 90° Carbureted	Click Image For Larger	VERTICAL Reeds, 6R5 Rod 23mm WRIST PIN HOLE STD.,+010. .020, .030, .040	100-275-2x $1,386.00
V6 90° Carbureted	Click Image For Larger	21.5mm WRIST PIN HOLE 6E5 Rod, HORIZONTAL Reeds STD.,+010. .020, .030, .040	100-270-3x $1,285.00
V6 90° Carbureted	Click Image For Larger	23mm WRIST PIN HOLE 6R5 Rod, HORIZONTAL Reeds STD.,+010. .020, .030, .040	100-275-3x $1,285.00
V6, 2.6 LITRE HPDI 150-200 HP ALL	Click Image For Larger	STD.,+010. .020, .030, .040	100-290-1x $1,636.00
200-225 HP V6 76 DEGREE 3.1L EFI    1994 - 2003 250 HP V6    1995 - 2003 DISH TOP PISTON		STD., +010. .020, .030, .040	100-285-1x $1,415.00
225-250 HP V6 76 DEGREE 3.1L 1990-94 DOME TOP PISTON		STD.,+.020, +.040, +.060	$1,667.00
3.3L HPDI	Click Image For Larger	STD., + .020, .030, .040	100-295-1x $1,750.00