| |
NISSAN TOHATSU POWERHEAD KITS PARTS PACKAGE KITS FOR REBUILDING
POWERHEADS
LOST?? See POWERHEAD KITS FOR US MADE BRANDS
These kits contain all the parts you will commonly
need to complete the overhaul of your outboard's powerhead. If the
determination has been made that you need to rebuild, we have the
necessary items! And the nice part is, you will pay less for the
kit than you would for the individual parts, as you save us time
in ordering. So you will have all the goodies you need to do the
job right.
For motors not listed,
contact me directly
for the specific application. It is likely I can provide the components you need. Feel free to
call
about your motor or purchasing any components of these kits.
NISSAN TOHATSU Rebuild kits include all of the following items, as required, unless noted:
-
PISTONS/ RINGS/ WRISTPINS/ RETAINERS
- COMPLETE GASKET & SEAL KIT
- CRANKSHAFT UPPER AND LOWER MAIN BEARINGS
- CONNECTING ROD WRIST PIN BEARINGS
- THERMOSTAT AND IMPELLER
- GASKET SEALING COMPOUNDS AND CRANKCASE SEALER
- EXPLODED VIEWS, ASSEMBLY AND TORQUE SPECS
- TECHNICAL ASSISTANCE FROM THE MASTERTECH.
HOW TO ORDER
Just add the kit you need to the shopping cart. Or use the quick order form to do the order with one page simplicity.
BUT BE SURE to fill out the little
separate boxes just below and submit first with YEAR, MODEL and SERIAL
#, and the OVERSIZE for the pistons! OR, you may add this info in
the special instructions area of the order form.
NOTE!! I reiterate, you
MUST PROVIDE THE YEAR, MODEL and SERIAL NUMBER as well as the PISTON OVERSIZE
when ordering. I cannot send you the correct parts otherwise!
Please
take the time to enter the model and serial number of your motor!
Also the oversize spec for the pistons. It will be stored in
the shopping cart and sent in with your order. Thanks!
| NISSAN/TOHATSU COMPLETE KITS |
| 2.5A, 3.5A |
STD.,+.05MM |
$120.00 |
|
3.5B
3.5 HP WITH SHIFT |
STD., +.05MM |
$125.00 |
|
| 5B |
STD.,+.05MM |
$165.00 |
|
| 8B, 9.8B |
STD.,+.05MM |
$310.00 |
|
| 9.9C, 15C, 18D |
STD.,+.05MM |
$345.00 |
|
| 9.9D2, 15D2, 18E2 |
STD.,+.05MM |
$345.00 |
|
25C2
30A3 |
STD.,+.020, .030, .040 |
$475.00 |
|
| 2 CYLINDER 40 HP M40C |
STD., +.05MM, +.020 , .030, .040 |
$475.00 |
|
| 2 CYLINDER 25C3,
30A4 |
STD., +.05MM, +.020, .030, .040 |
$475.00 |
|
| 2 CYLINDER 40C |
STD.,+.020, .030, .040 |
$475.00 |
|
| 3 CYLINDER 40D2, 50D2 |
STD.,+.020, .030, .040 |
$519.00 |
|
2 CYLINDER 70A2
2.913 SMALL BORE |
STD.,+.020, .030, .040 |
$475.00 |
|
2 CYLINDER 70A2
3.385 BIG BORE |
STD.,+.020, .030, .040 |
$475.00 |
|
| M60B, M70B |
STD.,+.020, .030, .040 |
$CALL |
|
| M90A |
+.020, .030, .040 |
$695.00 |
|
| 115,A 120A, 140A |
STD.,+.020, .030, .040 |
$895.00 |
|
Now that you have found what you need, please order it using the shopping cart above, the secure quick order form, or call in your order . We pay the freight out in USA on all orders over $100.00. Orders less than this amount will have a shipping and handling charge of $6.75 added. Some bulky and heavy items will incur additional charges. You will be notified beforehand if this is the case. Remember, all orders receive free technical support from the MasterTech! |
|
| |
Please review our Warranty, Returns & Refunds policies before you place an order.
DISCLAIMER
The information provided on these pages is correct to the best of my knowledge, however the MasterTech makes no warranty, express or implied, regarding the use of, results of, or liability created from, application of this data. This information is disseminated in good faith, however MasterTech assumes NO LIABILITY whatsoever in regard to this service. The information, software, products, and services published on this web site may include inaccuracies or typographical errors. Changes are periodically added to the information herein. Mastertech may make improvements to this site at any time. Parts ordered from this website may or may not be in dealer stock at the time of order. Thank you for reading.
Site best viewed at 1024 x 768 resolution or higher with Firefox 1.5-up, Netscape 6, or IE 5 or higher
© 1999-2008 MasterTech Marine
Revised 2-26-08
|
|